Showing posts with label colour. Show all posts
Showing posts with label colour. Show all posts

Tuesday, 1 March 2016

Milk Fibre and Bamboo

I am wanting to introduce different yarn blends in to my shop. To do this I need to firstly source different blends. I am aiming to use primarily Australian and New Zealand milled and grown yarns. To do this I have been researching the limited number of mills in Australia and finding out what un-dyed products they have in their range. Next step is to order small quantities of potential bases, dye them and knit with them to find out if I like them enough to be comfortable selling them as part of my range.

This past week I purchased three new to me blends, two are bamboo & wool blends (with different percentages of each) and the other is a milk fibre and wool blend.

First a little about these different fibres:

Milk Fibre
As the name suggests milk fibre comes from milk. It is created as a by-product of processing skim milk. A chemical process is used to extract, dry and then turn a powdered protein in to a fiber. It was first used during the 1930s and 40s to make wool and cotton go further. It is said to have anti-bacterial qualities and take colour very well (the protein in milk fibre was also known to be used in early outdoor paint).



Bamboo
Yes, the grass that Panda's eat! The insides of the stems are processed down and made into a fibre, it has a shiny finish similar to silk. It gives strength when combined with wool, while keeping a drape and breath ability.


My Experiment
In order to test out the new blends I put all three in to the same dye bath (labelled with brightly coloured yarn that would not change colour) and did two different dyeing methods.

Batch 1
First batch I dyed up in Strawberry Shortcake (a repeatable colour that I already have in the shop). This was so that I could compare how the colour takes between my current sock yarn (Gumboot Sock) and the three new bases. Look how differently it comes out across the yarns!

LtoR: Gumboot Sock, 16% milk fibre/85% wool, 50% bamboo/50% wool, 60% bamboo /40% wool
Batch 2
Next I chose to have a play. I tried some shallow immersion dyeing and squirted some dye onto different sections of the yarn, to see how the dyes would absorb and blend on each fibre. Again, some extremely varied results.

LtoR: 16% milk fibre/85% wool, 50% bamboo/50% wool, 60% bamboo/40% wool

The milk fibre yarn took up the dye a lot more than the bamboo, it is quite vibrant and dark. Of the other two, the one with the lower bamboo content seemed to take the colour better, but the one with more bamboo is a lot shinier and has more drape (this could also be due to the spinning method of the yarn as well, the 50/50 blend is a crepe style yarn, which is a bit more dense). The sheen and drape of the bamboo yarn is really lovely. I am looking forward to knitting with each of these blends to see how they work up.

Will any of these blends end up in the shop? Will have to wait and see how I like the finished projects.

Anyone who as worked with these fibres before I would be interested to get your feedback and thoughts.

Tuesday, 8 December 2015

A snap shot of my dyeing process

Dyeing yarn has become a huge part of my life now, but when I started out I was not sure what I was doing. I taught myself through experimentation, reading blogs and forums and watching podcasts.

I thought I would share a little of what I do - especially for those of you out there who see it as a mysterious and complicated thing. This is certainly not a comprehensive guide or the only way to dye, it is just a little of what I have taught myself.

1. Start with undyed/bare yarn - I have some yarn that comes in pre-measured skeins, like the ones in the top left, but I also buy yarn in larger hanks and on cones, that I wind off into skeins myself. I add additional ties to each skein to stop it from tangling.

2. I use Jacquard acid dyes - these are a powder dye, activated by acid (vinegar or citric acid). I currently have 12 different colours. I use a dust mask to protect myself while mixing the powdered dyes and make a stock of each colour (a mix of the powder and water) that I keep in squeeze bottles. Then when creating colourways, I mix the stock dyes together to create unique colours. I write down each of my recipes in a note book, with steps for each layer of dye.

3. To prepare the yarn for dyeing, I soak it in slightly warm water and a little bit of wool soap.

4. Most of the time when I dye I have an end result colour in mind, the example above is my Fuchsia colourway. I took a photo of the flower from my garden and mixed the dyes with the end result in mind.

5. I measure out the dye, writing down my recipe as I go, and add it to the pot, along with vinegar and turn on the heat. I then add the wet skeins of yarn to the pot and allow the dye to absorb, keeping the water at a steady heat just below a simmer. Once the water is clear (or close to it) I remove the yarn and add another dye mixture. I usually then unravel, or re-twist the yarn, to expose different sections to the dye and place it back into the pot. Depending on the colour I could repeat this part of the process a number of times.

6. Once the final layer of colour has been applied I keep the heat on for a little longer and then put the lid on and turn off the heat. I leave the yarn in the pot and leave it to cool. This stage allows any remaining dye to be taken up by the yarn and provides residual heat to set the colour.

7. When the yarn is cool, I drain off the water and rinse, before leaving it to soak in slightly warm water and a wool soap. This removes any excess dye and washes away any vinegar.

8. Next is to get the yarn dry. For my superwash wool I give it a little spin in the washing machine (in a delicates bag) and then hang it over a drying racks to get plenty of airflow. I rotate the skeins to  help them dry evenly.

9. Final stage once the yarn is dry is to rewind the yarn back into a neat skein. I cut all of the ties and wind it into a skein. This realigns the colours and tidies up the skein after going through the dyeing process.

As I mentioned earlier, this is just one way that I use and I am mostly self taught. There are so many ways to dye, you can be very scientific or very relaxed and organic.

Tuesday, 3 November 2015

Set up Shop

The set up show e-course finished at the end of October. It was an information packed month of daily emails and interesting discussions on Facebook.

I have learned a lot and gained encouragement and confidence.

A big thing that stuck in my mind from doing the course was that your business will never be finished or perfect, so I have decided to stop preparing and today I opened my shop (you can click on the tab at the top of the page and go there now for a look!).

It is a big leap of faith. Will anyone like my colourways? Will anyone choose to spend their hard earned money to buy my yarn? Have I properly figured out my shipping methods? Are all the elements of my shop set up? I guess only time will tell.

A new phase of learning and development now starts and I am excited to see where it takes me.

Sunday, 18 October 2015

Rest Day and Course Progress

Today is the second "rest day" of the Set up Shop e-course. We are two-thirds of the way through and I am enjoying the process of taking time each day to focus on an aspect of my new venture.

We have covered off a lot of topics including: branding, product descriptions, packaging, postage, pricing, photography, shop about page and policies, order systems, and financial records.

I have made a little progress every day, getting all the details sorted out. Some days of the course I have felt quite comfortable with, like setting up an organisation system for emails and financial recording - I was able to get these sections done quickly and without much thought. Other topics have taken multiple days, numerous drafts and much more thought.

Today I wrote a template for the product descriptions for the shop. I am also going to keep a separate file that contains a description of each colourway. I can then combine these two files to use when I list a yarn.

Another thing I tackled today was designing my ball bands. I have gone fairly basic, using my passioned flower image on the left hand side and incorporating all the details in the white space on the right. Not sure that this will be the final version, but I'm happy with what I have been able to come up with (you will have to wait for the shop launch to check them out).


I still have a lot of work to do - I need to re-work my policy page, finish my list of tags, properly research postage and packaging costs plus there is still several more lessons to go. I am loving every minute I spend on this and excited to see where it will take me.



Saturday, 10 October 2015

Yarn dyeing - my journey so far

It was only at the beginning of this year that I took the plunge to try dyeing yarn.

I have experimented with sprinkling powder directly into the pot



I have squirted stock dyes directly into the pot and on to yarn with a vague plan and no intention of being able to replicate the outcome, and wound yarn for my first attempt at self striping.




I have progressed quickly from this ad hoc kind of approach, to dyeing with more intention. Basing my colour decisions on inspiration and planning the outcome of the yarn. I am taking a lot of photo's mostly of flowers and leaves, but also of the sky, sea, graffiti and anything else the catches my eye.

I now take careful and detailed notes as I dye. Tracking exact amounts of dye, the method used, steps taken and time the yarn spends in the pot.

Iris and City Sunset

Teal not Green and Winter Roses
Yarn dyeing has definitely become an obsession, a passion that I want to pursue as a business and share my creations and inspirations with other crafters.

This is a big and scary step! Putting my creations out there in to the world for judgement, not only that but embarking on a small business without much experience is quite daunting.

I have enrolled in a short e-course by Create & Thrive, called Set Up Shop. It is a step by step guide, covering all aspects of what goes in to setting up an on-line craft business. I am finding it extremely useful and thought provoking. It has been reassuring, some of what we have covered I had already considered myself. I just never had the confidence to put it in to action. Having someone who has already experienced success in this area providing this guide has given me the extra drive to push ahead.

Stayed tuned to see how things progress from here. Much work is going on in the background. I will post progress and thoughts of the course as well as updates on the shop.





Wednesday, 30 September 2015

What inspires me

Most of my thoughts on the blog so far have been directly about knitting or yarn. Sharing my projects and progress.

As the seasons change and the spring flowers take over the garden I thought I would share what is currently inspiring me.

In my very first post I wrote about how craft feeds the soul, the grounding factor that creates peace and provides escape. The action of making something, creating an idea in my head, and then using my hands to make that idea come to life.

This is definitely the driving force behind why I craft. It is my escape, my happy place and my creative outlet.

Everyday, out in the world, I take note of how colour occurs in nature. The combinations of colour and the vibrancy catch my eye. How amazing are these colours from my garden this morning!?!?!

How can seeing this beauty in nature not lead to inspiration?



To begin with it makes me happy. I put hard work into my garden throughout the year and these are the results of that work. Proud displays of the care that I have taken.

Flowers and foliage are also great guides on which to base colourways for yarn. Nature has a way of getting things right, so it is fun to try to capture that in dye.

I grab my camera out frequently to capture these types of images. Fuel for my creative fire.

What inspires you? Where does your craft inspiration come from?


Wednesday, 16 September 2015

Knitrospective - Shawls

What makes a great shawl? Colour? Shape? Size? Lace? Beads? Garter?

Shawls are a regular in my knitting rotation. I have a lot in my queue and library. Once I have completed one I am searching for the next one to cast on.

They are go-to accessory pieces, especially for my work wardrobe. Essential for combating the chill of air-conditioning and also for adding the "knitterly touch" to my outfits.

I began with small, one skein shawls like the Multnomah by Kate Ray, Mizzle by Patricia Martin and Pimpelliese by Christine Ebers.

Pimpelliese
I now enjoy larger multi-coloured, lace or beaded shawls. Although there is always a place for a more simple, one skein shawl in the knitting rotation (my recently knitted Reyna is an example of this).

Nuvem has been on my needles twice, and could definitely be knit again.



My Hope

The two most intricate shawls I have knit have not been for me, but made as special gifts. The My Hope for my sister on her wedding day and Bella Botanica for my mother-in-law for Christmas. Both had beading and lace work and I loved the process of knitting each of them. I know both have been worn numerous times, which makes me happy. What I am disappointed about it that in both cases I never took proper finished object pictures, only progress and blocking shots.



I think I will at some stage have to knit a lace and bead shawl for myself, but at the moment I am enjoying the squishy garter and fun colour combinations from patterns like Drachenfels and Moonraker by Melanie Berg.

Moonraker
A shawl that was in my queue for a very long time was Bloom, which I finished earlier this year. I wrote a full blog post on the finished object. I have worn it at work and received many compliments - it has some wow factor. I am thinking about yarn combinations for another one.

Bloom
So what is the best kind of shawl? It's much too difficult to decide, I guess I will have to keep knitting more to try out more patterns, colour combinations, shapes and techniques.

Sunday, 30 August 2015

Digging into the stash - knitting with that "special skein"

After taking the time to review my stash in preparation for Bendigo (see previous post), I rediscovered some amazing yarn. Not forgotten, more like I had moved it to the back because I did not know what to do with it and felt that it was too special to knit with.


I found a simple shawl pattern on Ravelry; Reyna by Noora Laivola. I liked that it had garter and some lace sections, without being a complicated pattern. As I wanted the yarn to be the star.


During this dig into the stash, I also realised how many partial skeins I have. Leftovers from socks and shawls, but not enough to think of as scraps. So out came the scales and I weighed the portions that I had, sorting them into size piles as I went. The Moonraker Shawl, by Melanie Berg, seemed like the perfect way to incorporate a couple of my smaller skeins into a large project.

My small skeins are from two projects that I really enjoyed. They are a sparkly purple left over from my Low Tide Cardigan and a sparkly blue/grey from the My Hope shawl I made my sister for her wedding.


   

Sunday, 9 August 2015

Finished Object - Bloom Shawl

It was so great to come back from Bendigo with yarn for specific projects and so motivating to cast on straight away.

When I arrived home on the Sunday afternoon I immediately balled up the charcoal and teal corriedale I had purchased for Colleens Crafts to make the Bloom Shawl by Kiri FitzGerald-Hillier.

The version of the pattern I followed is the original as it was published in Issue 31 of Yarn Magazine.

My default for reading patterns is the written instructions and then referring to a chart, if provided, as a reminder guide as I complete each round. After completing this pattern, my advice for anyone else is to follow the charts, as the written directions seem to be inaccurate or at least confusing in parts.

First thing I did was find a tutorial on how to do the pinhole cast on - I used the one from Very Pink Knits. It took me a couple of tries to get it right but overall not a hard thing to master.
.
The directions were for 5 dpns, but I knit the whole motif on magic loop. One thing that was not clear in the written directions was where to place markers - to split the motif into its four sections. If I had realised this earlier I would have been able to get this information from the chart. I guessed a little as I went along and I think in the end it is not noticeable that I fudged it a bit.
I made several modifications in the wing sections. For the decreases on both the left and right wings I knit two together through the back loop. I tried a few different decreases and decided that in the garter stitch I liked the look of this method best. I flipped the wings, so that the decrease side was the top edge, the finish and angle of the wing seemed to lay better that way. I also connected the blacks at the top of the motif together by knitting the last black stitch of one wing with the first black stitch of the other.

This was a super quick knit - it took me 15 days and zoomed along. I think part of the reason for this, apart from being knit in a DK, was that until you get to the edging there are really not many stitches on the needles, so the rows are short.

In the end I used all but 8 grams of the charcoal (from 213 grams). I do have plenty of the teal left, having only used 40 grams of a 100 gram skein.

I wet blocked the shawl, using blocking wires on the motif to make it square. Then pinned the wings and edge into shape around that square. I also pinned out each point of the lace pattern.





Saturday, 25 July 2015

The Bendigo Haul

Shawl pins from All Buttoned Up
I had such as wonderful time at Bendigo this year.

Did I stick to my list? Pretty much.

I have added all my new yarn to my Ravelry stash already, but wanted to do a blog post to highlight all the great vendors.

Needles and cables - all purchased from Fiberific!.
Two ChiaoGoo "Spin Cables", 75cm and 125cm. For most things I prefer these over the red twist cable as the are more flexible and they spin at their base which I really like.
Wool N Wire stitch markers
Three sets of the "Twist" Lace needle tips in sizes 2.75mm, 3.5mm and 4mm - sizes that I regularly use.

Accessories and stitch markers
Two shawl pins from All Buttoned Up - Vintage Jewellery Melbourne.
A set of blinglets medium sized stitch markers from Fiberific!
A set of stitch markers from Wool N Wire


Yarn
Dyed by Hand Yarns (top three skeins):
White Gum Wool DK - 2 skeins in Purple Sea Urchin
Tough Stocking (4ply)- 1 skein in Blue Ringed Octopus
Tough Stocking (4ply) - 1 skein in a "one hit wonder" purple colourway

Colleens Crafts (first two, bottom row left to right) :
Corriedale DK - 2 skeins in Sage Green Tones
Corriedale DK - 2 skeins in Charcoal

Mayhem & Chaos (middle right and bottom right):
Crazy Eights (DK/8ply) - Voodoo Lady - enough for a sweater (thinking this will be the main colour for the Pixelated Pullover)
Lollisox - Taste the Rainbow - sample of fingering weight




Tuesday, 30 June 2015

Cupcake mittens, deadlines and making changes to the pattern

My sister requested that I make her Cupcake Mittens.They looked super cute, so agreed that I would give them a go.

I am satisfied with the end result and pretty happy with my colour work, but these were a hard slog.

The beginning of this project caused me frustration. I had trouble getting gauge, first they were too loose, then they were too tight - playing with needle size and stitch counts until I on the fourth try I was happy with the cuff. I also found that by knitting the cupcakes on the palm as well as the back of the hand the mitt was very tight (partly I think due to my inexperience in colour work). So I chose to rip back to the cuff and change the pattern. I knit the cupcakes on only the back of the hand, five on the first row, four on the next and then alternated those two rows. I also knit three plain rows in between, in order to give myself a break from the colour work, provide an opportunity to knit in ends as I went and to hopefully prevent the overall mitten from being too tight.

I also changed the pattern further, by making the mitts convertible. I used the directions from the ChemKnits tutorial for transforming any mitten knitting pattern into convertible mittens.

After three repeats into the cupcakes on the first mitt, I thought that the thumb as written in the pattern was going to end up making the mitts too tight and not sit correctly, so I made the decision to start adding in a thumb gusset. The end result was a stumpy looking thumb that looked weird and felt wrong. I blocked it so see how it would end up, and had my sister try it on. Immediately I knew I had made the wrong decision with the thumb. I put that completed mitt aside and started the second one, following the pattern.

Although the first mitt ended as a bit of a fail, it had actually knit up quickly once I had started. So I was keen to get going on the second one to get it right. But the one by one twisted rib on 2mm needles broke me and I struggled to get it going. I knew I had a deadline, my sister was waiting for these mitts and now, not only did I have to knit the second one, but I had to go back and see if I could save the first!! But the brain is a funny thing, right? I wanted to cast on other things, or didn't feel like knitting at all. I think if I had no deadline and the first one had been a success I would have been into it and quickly finished the second. But with the weather getting colder and my sister eagerly expecting the finished pair, progress on the second one was slow.

I think I was also dragging on knitting it, because I knew I was going to have to tackle fixing the first one when I was done.

To begin this process I looked to see if I could rip it out from the bind off, but because it had been blocked, the ends were hard to find and it had fused together a bit, not felted, but just difficult to rip out. So I grabbed a pair of scissors and cut the top off the mitts, just above where I needed to restart with the thumb as written in the pattern.



As painful as that was, it ended up being the best option. Once I had taken the plunge, ripping out and picked back up where it needed to be I felt so much better and it took me less then a week to then knit up the rest of the mitt.

Lessons learned:

  • I really do not react well to deadline knitting (when the recipient is expecting the item).
  • I should have followed the pattern;
  • or at least read it through first - perhaps if I had read the entire pattern I would have started a thumb gusset earlier, preventing the stumpy thumb I created.
  • I enjoy the result of colour work and would like to do more, perhaps on a jumper.

Tuesday, 2 June 2015

First attempt at self-striping sock yarn

After dying for longer colour repeats on a chunky yarn, I decided the next thing to try was a self-striping sock yarn.

I used the same method for winding and dying the yarn as I used for the previous experiment and again sectioned the yarn into four equal sections.

Colours used this time around:
a light blue/green - mixed using emerald and turquoise
a dark green - mixed using emerald and turquoise
light purple - straight from dye stock
gun metal - straight from dye stock

The bottom image is the toe of a sock, I could not wait to cast something on. I am fairly happy with how it has come out, although the stripes are not very thick. For thicker stripes I am either going to have to limit myself to two colours per skein, or find a new piece of equipment to wind longer skeins.











Monday, 25 May 2015

Dying for longer colour repeats - Part 2

I am so pleased with how this turned out, especially given that it is my first attempt at longer colour repeats.

As promised last week, here is my dying process, in pictures.


After the skein was dry I was keen to get it back into a shorter skein, but a little worried about how I was going to do this without creating a giant knot! Luckily for me the door handles in my craft room are the perfect distance apart to loop my long skeins around and then wind on to my umbrella swift. I managed to get it wound without any tangles and it didn't take too long.


I am sending this skein to a friend. She had seen the yarn I had dyed to match my winter coat and asked if I could dye her some chunky yarn for a cowl she wanted to knit. I am excited to see how it will knit up.

I now have ideas for trying gradients and self striping, based on what I was able to achieve with my first attempt at longer colour repeats.

My equipment is clearly very basic but for now it works. I am getting results that I am really happy with and having fun along the way.

Saturday, 23 May 2015

Dying for longer colour repeats - Part 1

Up until now all my dying projects have resulted in highly variegated colour-ways. I have kept the skein the size I purchased it in, and dyed the entire skein in one go.

So, for this dye project I made a longer skein and dyed it in four sections.


First I had to figure out how I was going to create a longer skein. I do not have a warping board, or even flat back chairs that I could run the yarn between.


I scanned the house for something that could work. I settled on the coffee table, flipped upside down, and wrapped the yarn around the legs in a Z pattern.


My first attempt I confused the way I was wrapping the yarn, not realising until I was tying it. This led to rewinding the yarn back into a ball, untangling as I went. The second attempt I chanted to myself as I wrapped - over, under, over, under - so I would not make the same mistake again.

 I tied up the skein with numerous ties, made it into a loose crochet chain and left it to soak.

Now for the dying...
I dye in my kitchen and do not have the space to attempt hand painting, so I needed a plan to that would allow me to still do immersion dying but in sections.

I set up my baking tray on the stove top, and then a tub for the undyed portion of the yarn and a pot for the dyed portions.


I had put temporary ties in the long skein to split it in to four sections, as I fed each section into the pan I removed these ties and made sure that the dye overlapped at these points so there was no white.

Colours for this project:
section 1: emerald and turquoise
section 2: purple and periwinkle
section 3: orange and russet
section 4: sky blue

I posted a mid-dying colour photo on Instagram (link on the left).

Check the blog next week to see the colour progressions, what solution I come up with for re-skeining my long skein back to a "normal" sized skein and the finished dying project.


Thursday, 7 May 2015

Dye project - to match my winter coat

Years ago I bought a pink coat. Since then I have not really had any accessories that matched. Now that I have an urge to dye everything, I thought I could try to make my own colourway to knit into a beanie and mitts.

I know I could easily just knit in a black or neutral colour, but I wanted something bright and cheery.

For this experiment I used my large baking tray and heated the water on the stove top.

I used Skein Yarn, two of her DK natural skeins. The base is really soft and springy.

Colours for this project were pink, russet, orange, purple and gun metal. Using my solution stock and squeeze bottles.

The yarn was pre-soaked in water and then bought up to temperature in vinegary water. The yarn was placed in a semi-circle/horseshoe shape in the pan.

On the edges I layered the pink, russet and orange  - squirting the dye solution directly on to the yarn. The purple and gun metal was squeezed on the middle section. I let it cook a little and then added more colour to the whiter spots and squirting some dye directly into the water rather than on the yarn.



Once I was happy with the colours I covered the tray with foil, kept it on the heat for about 20mins and then left it to steam and cool. Only when the water was completely cool did I drain, the now clear water, and soak in fresh cold water. As the yarn hung to dry, I could already see the effect I was able to get by mixing the pink, orange and russet and then the blending at the edges with the gun metal and purple.

I am really pleased with the results. I had the idea in my head of how I wanted it to turn out and it actually worked! The mixture of orange and pink together created a really great colour, that will go well with the coat and the purple and gun metal break up the pink and helped to mute out the russet.








Friday, 24 April 2015

Playing with colour

Although I have not had a huge amount of time to spend dying, and I also can't invest in skeins and skeins of bare yarn, I have done a little more and have played with a comparison between different yarns and different techniques.

I now have ten different colours of acid dye. I expanded my collection recently after deciding I wanted to get the primary colours to begin experimenting with mixing colours. I am familiar with the basic colour wheel and know what colours are pleasing to me both by themselves and side by side but my crafting up until now has not involved any mixing of colour or creating my own palette. I have purely put pre-made colours together into my handcraft. So mixing colours and seeing the outcomes of that on yarn has been interesting and exciting.

I have prepared each colour as a dye stock. Up until now my experimenting with dye has been sprinkling the powder directly into hot vinegary water and watching it mix and react with the yarn.

This time I had a thought process of wanting to try a different method and these are the results.

Skein 1

  • 100% wool
  • pre-soaked in plain water, then bought up to temperature in plain water
  • small amounts of mixed and diluted dye stock added to the water
  • started with a yellow, then added a light blue and gun metal
  • At this point I thought I had what I wanted, so added vinegar to the water and set the dye.
After it dried, it was way too pale, and there was too much white and very light yellow for my liking. So it got another bath!

Second round:
  • bought the skein up to temperature in water that just covered it
  • applied diluted colour to patches that seemed the lightest, turning the wool and adding little bits all over of all of colours (and combinations of them)
  • Finishing with a final vinegar treatment at the end to set everything.

Skein 2
  • 85% super wash merino, 15% nylon
  • pre-soaked in plain water, heavily twisted into a skein
  • mixed a custom green and added the dye to hot vinegary water before adding the skein
  • let the dye exhaust, turning the skein as it soaked for even coverage
  • took the yarn out, unravelled it, then returned it to a fresh pot of hot vinegary water (low level)
  • focussed on the white sections, squirting pure dye solution directly on the yarn.


I love both skeins. Love them for their differences and what I learned from the mixing and diluting process and from the different ways that yarn takes up the dye.